TI Automotive Fuel Pump Meets Direct-Injection Challenge

LONDON, May 18, 2004 -- TI Automotive is introducing an all-new, dual-channel, single-stage (DCSS) line of fuel pumps that the company predicts will set a new industry standard for efficiency.

Developed by a TI Automotive research and development team in the United States, the turbine pump is the first, cost-efficient fuel pump designed to meet the high-fuel-pressure requirements of direct-injection engines, according to Manouchehr Kambakhsh, the company's vice president of global advanced engineering.

"The DCSS pump will enable automakers to increase fuel efficiency, reduce emissions and improve the overall performance of future petrol engines," Kambakhsh said. "Within the next six years, we expect this new design to replace a majority of the fuel pumps that we produce on a global basis."

In addition to more conventional applications, the new pump is suited for use with saddle-style fuel tanks found on many high-performance vehicles.

Developed at a cost of more than 10 million pounds over the last two years, the new pumps will be produced at TI Automotive manufacturing facilities in Neuss, Germany, and Caro in the U.S.

"The DCSS pump is engineered to provide automakers with improved efficiency, higher fuel pressures and increased pump life," Kambakhsh added . "Our new pump offers the most significant gain in pump efficiency in years. It operates at efficiency levels of up to 30 percent, nearly 50 percent higher than the typical 20 percent efficiency of today's turbine pumps."

TI Automotive's innovative DCSS pump incorporates two rows of turbine blades that feed two parallel high-pressure pumping channels, compared to a conventional single-stage pump that uses an impeller with a single row of blades at its outer edge.

"The end result effectively doubles the flow of fuel through the pump," explained Ernst Kuhlen, director of global fuel delivery pumps and modules. "Innovation and technology development, as demonstrated by these new products, form the core of our company's strategy for future growth."

For high-flow/high-pressure requirements, the DCSS pump uses a 50-mm pump housing coupled to a proven 39-mm motor used for the company's present, single-stage T-8 family of pumps. "Since we already had a reliable pump motor, we were able to shave a considerable amount of DCSS development time," Kuhlen noted.

Designers concentrated on creating a larger, 50-mm inlet housing and a larger impeller to make room for a unique second row of turbine blades. The patented dual high-pressure design maintains velocity in the fuel channel by splitting the inner and outer flow paths.

The unique pumping sections were designed in parallel, not in series as in other two-stage pump designs, and the impeller was engineered with unique curved-leaning blades, both of which help to reduce fuel turbulence and increase pump output.

"Present single-stage turbines only give you a maximum pressure of about 5 bar and flow rates of 180 liters per hour," Kuhlen explained. "That's far short of the fluid pressures and volume needed for advanced direct-injection engines."

The DCSS 39/50 produces flow rates of 200 to 240 liters per hour at pressures ranging from 4 to 6 bar and easily meets direct-injection performance criteria.

Kuhlen also pointed out that present single-stage pumps only operate at about 20 percent efficiency. "We've consistently scored 30 percent efficiency at 240 liters per hour at 4 bar, and at higher 6 bar pressures, we can achieve greater than 26 percent efficiency at 200 liters per hour."

In critical "hot fuel" tests, the DCSS 39/50 also significantly outscored its competitors. Other single-stage turbine pumps show flow losses ranging from 12 percent to 32 percent at operating temperatures up to 67 degrees C (153 F). The DCSS 39/50 showed only an eight percent drop in flow under identical test conditions.

"Heat is also critical in direct-injection engines," Kuhlen noted. "Not only do we need to deliver a cooler fuel, but engine-mounted, direct- injection pumps hold high tolerances, and if they are exposed to high temperatures, the varying coefficients of thermal expansion in the pump material can create lockup."

The benefit of increasing output without increasing motor size also provides much greater durability. "Because the TI 39/50 provides increased fuel flow, we can reduce the revolutions per minute (RPMs) of the pump motor. That reduces motor brush wear and significantly extends the life of the motor," Kuhlen added.

In durability tests, the DCSS 39/50 exceeded 10,000 hours of continuous operation, more than double the typical automaker requirement of 5,000 hours.

TI Automotive is the world's leading supplier of fluid storage, transfer and delivery systems including brake, fuel and air conditioning applications. Based in Warren, Michigan, U.S.A., the company employs over 20,000 people at more than 130 facilities in 29 countries on six continents. Further information about TI Automotive is available on the company's website at www.tiautomotive.com .

NOTE TO EDITORS: Digital photography is available by contacting Laura Oliveto (loliveto@usautocom.com ); CONTACT: Company Contact: Andy Anderson of TI Automotive, +1-586-427-3726, ganderson@us.tiauto.com ; Media Contacts: Keith Webb of Edson Evers and Associates, +44-(0)178-65-255-146, keith@edsonevers.com ; or Larry Weis of AutoCom Associates, +1-248-647-8621, lweis@usautocom.com , for TI Automotive. Web site: http://www.tiautomotive.com