Compare Safety Features on 1998 Toyota Corolla 4dr Sdn LE Auto 2016 Tesla Model S 2016.5 4dr Sdn AWD 90D

Click to print

Compare Cars Side by Side on
Safety Features

To remove some of these vehicles and add additional ones, uncheck the vehicles you want to remove and click continue.

1998 Toyota Corolla 4dr Sdn LE Auto

3-point front shoulder belts w/pretensioners, adjustable anchors
3-point rear shoulder belts
Child-protector rear door locks
Driver & front passenger air bag Supplemental Restraint System (SRS)
Side-impact door beams
Front/rear energy-absorbing crumple zones

Crash Test Results for the 1998 Toyota Models:

Car	Frontal Star Rating		Side Star Rating		Rollover Resistance Rating
Car	Driver	Pass.	Front Seat	Rear Seat	Rollover Resistance Rating
1998 Toyota 4Runner	3	3	Not Tested	Not Tested	Not Tested
1998 Toyota Avalon	4	5	5	4	Not Tested
1998 Toyota Camry	4	5	3	3	Not Tested
1998 Toyota Corolla	4	4	3	3	Not Tested
1998 Toyota RAV4	4	4	Not Tested	Not Tested	Not Tested
1998 Toyota Sienna	5	5	Not Tested	Not Tested	Not Tested
1998 Toyota Tacoma	4	3	Not Tested	Not Tested	Not Tested
1998 Toyota Tercel	Not Tested	Not Tested	3	4	Not Tested

Service Bulletins for 1998 Toyota Tercel 4dr Sdn LE Auto

1998 TOYOTA COROLLA:

Bulletin Number: 00304
A/C COMPRESSOR INSTALLATION PROCEDURE. *MR

Bulletin Number: 021899
SUBJECT REGARDING DAYTIME RUNNING LIGHT RELAY SENSITIVITY IMPROVEMENT. *TT

Bulletin Number: 394
SUBJECT REGARDING REAR SUSPENSION SUPPORT. *TT

Bulletin Number: 395
SUBJECT REGARDING FRONT SUSPENSION PLATE WASHER. *TT

Bulletin Number: 970822BO0025
SEAT COVER REPLACEMENT FOR SIDE AIR BAG EQUIPPED VEHICLES. *YC

Bulletin Number: 970829PG007
GENERAL INFORMATION ON PRE-DELIVERY SERVICE FOR SATISFYING YOUR DEALERSHIP'S NEW CAR CUSTOMERS. *YC

Bulletin Number: 97101397012
SUBJECT ON MUDGUARD INSTALLATION INSTRUCTIONS. *YC

Bulletin Number: 980825
THE CENTER CONSOLE STEREO COVER OPENING ASSEMBLY HAS BEEN IMPROVED TO INCREASE THE STRENGTH AND DURABILITY OF THE COVER HINGE. *YC

Bulletin Number: 980827
INFORMATION ON DECK LID CLOSING EFFORT. *YC

Bulletin Number: AX00101
TECHNICAL SERVICE BULLETIN REGARDING RETRO-FIT INTERNAL TRUNK RELEASE KITS. *TT

Bulletin Number: AX00499
SUBJECT REGARDING TOYOTA DINGHY TOWING GUIDE. *TT

Bulletin Number: BO01099
INFORMATION ON FRONT CUPHOLDER VERSATILITY ON VEHICLES WITHIN CERTAIN VIN RANGES. *TT

Bulletin Number: BO01498
INFORMATION ON INTERIOR DOOR LINK IMPROVEMENT. *YC

Bulletin Number: BO02498
TO REDUCE DECK LID CLOSING EFFORT ON VEHICLES STARTING WITH VIN 1NXBR12E1WZ042704, THE LUGGAGE COMPARTMENT WEATHERSTRIP HAS BEEN IMPROVED. *TT

Bulletin Number: BO02598
CENTER CONSOLE STEREO COVER OPENING ASSEMBLY HAS BEEN IMPROVED TO INCREASE THE STRENGTH AND DURABILITY OF THE COVER HINGE. *YC

Bulletin Number: BO02601
SUBJECT REGARDING SHOULDER BELT ANCHOR TAPE SET. *YD

Bulletin Number: BO02698
EXPERIENCING WATER LEAKING INTO REAR CAB. *YC

Bulletin Number: BR00200
INFORMATION CONCERNING A NEW FRONT DISC BRAKE PAD KIT FOR FRONT BRAKE VIBRATION. *TT

Bulletin Number: DL00198
REPLACEMENT OF THE FRONT AXLE HUB NUT. *YC

Bulletin Number: EG01198
INFORMATION ON OXYGEN SENSOR IMPROVEMENT. *YC

Bulletin Number: EL00498
INFORMATION ON THE SPOILER LIGHT REPLACEMENT PROCEDURE. *TT

Bulletin Number: EL00498
REPLACEMENT PROCEDURE FOR THE SPOILER LIGHT.

Bulletin Number: EL00698
SOME VEHICLES MAY EXHIBIT A DELAYED UPSHIFT TO OVERDRIVE AFTER CRESTING A HILL WITH CRUISE CONTROL ENGAGED. *YC

Bulletin Number: EL00798
SUBJECT ON DRL RELAY SENSITIVITY IMPROVEMENT. *YC

Bulletin Number: PG004-97-Obsolet
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.

Bulletin Number: PG006-01-Obsolet
Technical Service Bulletin: OBSOLETE NOTICE: July 31, 2018: This bulletin is now obsolete. Please see T-SB-0304-17.

Bulletin Number: Safety Recall an
Update on Technician Certification Requirements.

Bulletin Number: ST00100
SOME VEHICLES MAY EXPERIENCE A SQUEAKING NOISE FROM THE FRONT SUSPENSION. *TT

Bulletin Number: ST00598
CONCERNS OF STEERING COLUMN NOISE. *YC

Bulletin Number: ST00601
SUBJECT REGARDING STEERING RACK END NOISE. *TT

Bulletin Number: SU00300
SUBJECT REGARDING PART NUMBER CHANGES MADE TO THE REAR SUSPENSION SUPPORT SUB-ASSEMBLIES AND SUSPENSION SUPPORT NUTS. *TT

Bulletin Number: SU00400
INFORMATION REGARDING A PROCEDURE DEVELOPED FOR REMOVAL AND INSTALLATION OF THE FRONT SHOCK ABSORBER ON CERTAIN VEHICLES DUE TO THE ADDITION OF PLATE WASHERS BETWEEN THE FRONT SUSPENSION SUPPORT AND SUPPORT NUTS. *TT

Bulletin Number: TC13-019
SUMMARY TO BE PROVIDED ON A FUTURE DATE.

Bulletin Number: T-PG006-00 Obsol
This bulletin is now obsolete. Please see T-SB-0054-13.

Bulletin Number: T-SB-0014-11 Rev
TSB: The purpose of this service bulletin is to provide information regarding the installation of the correct torque converter bolts during automatic transmission/transaxle assembly replacement. Incorrect torque converter bolts or missing w

Bulletin Number: T-SB-0043-14
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased.

Bulletin Number: T-SB-0043-14 Rev
TSB: The Immobilizer and Smart Key Reset is a feature that allows the registration of new keys when all master keys are lost. Once the system is reset, all previously registered keys will be erased. Follow the procedures in this bulletin to

Bulletin Number: T-SB-0054-13
California (CA), Federal (FED), and 50 State Certified emission control underhood labels (emission labels) may be obtained through your dealership?s Parts Department utilizing standard replacement parts ordering procedures. Follow the guide

Bulletin Number: T-SB-0057-18
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin No. T-SB-0043-14. ? Applicability has been updated to include 2017 ? 2018 model year Toyota vehicles. Service Bulletin No. T-SB-0043-14 is obso

Bulletin Number: T-SB-0071-11
SUMMARY TO BE PROVIDED ON A FUTURE DATE.

Bulletin Number: T-SB-0071-11 Rev
The purpose of this service bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL ?ON,? shifting issues, and/or transmission damage. Use the information in this bulletin when

Bulletin Number: T-SB-0101-11 Rev
TSB: When servicing interior electrical switches and components, please note the precautions in this bulletin to avoid damaging electrical components and switches. Many lubricants, cleaners, and automotive chemicals contain silicone or othe

Bulletin Number: TSB-0122-11
TOYOTA: INFORMATION PROVIDED FOR REPLACING THE SEAT COVERS FOR VEHICLES EQUIPPED WITH SIDE AIRBAGS. *PE

Bulletin Number: T-SB-0122-11 Rev
Beginning in 1998, Toyota introduced side airbags as optional equipment. Toyota does NOT recommend replacement of original seat covers with non-Toyota leather or other seat cover materials on vehicles due to the following: Seat covers NOT

Bulletin Number: T-SB-0134-14
TSB: The purpose of this bulletin is to provide precautions to follow when installing an automatic transmission/transaxle assembly to avoid MIL "ON" shifting issues and/or transmission damage. Use the information in this bulletin when insta

Bulletin Number: T-SB-0141-13
SUMMARY TO BE PROVIDED ON A FUTURE DATE.

Bulletin Number: T-SB-0141-13
A new Special Service Tool (SST 09709-00002) has been introduced to aid in the inspection procedure for certain vehicles equipped with a floor pedal-type parking brake system. This bulletin references the correct method for installing the B

Bulletin Number: T-SB-0144-08_Obs
TSB: OBSOLETE NOTICE November 21, 2017: This bulletin is now obsolete. Please see T-SB-0304-17.

Bulletin Number: TSB018217
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes SB No. T-SB-0101-11. Applicability has been updated to include 2016 ? 2017 model year vehicles. Service Bulletin No. T-SB-0101-11 is Obsolete and any printed

Bulletin Number: T-SB-0185-13
The following procedures are recommended during routine maintenance or in the event of a customer concern for wiper performance.

Bulletin Number: T-SB-0218-17_Rev
TSB: REVISION NOTICE July 20, 2017 Rev1: Applicability has been updated to exclude 2007 ? 2017 model year Avanza vehicles. Some hazardous material treatment and handling regulations at the state and local level define the pre-disposal deplo

Bulletin Number: T-SB-0304-17
TSB: Vehicle replacement certification labels (the vinyl label installed on the driver door or door post) and VIN plates (the metal plate riveted to dashboard) may be available from Toyota, provided the request meets one of the criteria lis

Bulletin Number: T-SB-0304-17_Rev
TSB: REVISION NOTICE July 31, 2018 Rev2: ? The Supersession Notice has been updated. January 11, 2018 Rev1: ? The Supersession Notice has been updated. Any previous printed versions of this bulletin should be discarded. SUPERSESSION NOTICE

Bulletin Number: T-SB-0304-17_Rev
TSB: SUPERSESSION NOTICE The information contained in this bulletin supersedes Service Bulletin Nos. PG021-88, PG015-89, PG0015-90, PG002-91, PG002-93, PG005-97, PG007-01, PG007-07, and T-SB-0144-08. Service Bulletin Nos. PG021-88, PG015-89

Bulletin Number: TS-BO030-01 Obso
This bulletin is now obsolete. Please see T-SB-0185-13.

Bulletin Number: T-TT-0010-10 Rev
Tech Tip: Low battery voltage can contribute to a MIL "ON" condition for P0335 (Crankshaft Position

Bulletin Number: T-TT-0213-13
Toyota vehicles are equipped with Supplemental Restraint Systems (SRS), including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the

Bulletin Number: T-TT-0213-13
Toyota vehicles are equipped with SRS, including various airbags and in some models, seat belt pre-tensioners, to help reduce the risk of injury in a collision. If a customer expresses any concerns that the SRS airbags or pretensioner devi

Recalls for 1998 Toyota Tercel 4dr Sdn LE Auto

1998 GULF TOYOTA COROLLA

NHTSA Campaign ID:

98V277000

Component:

WHEELS:LUGS/NUTS/BOLTS

Manufacturer:

GULF STATES TOYOTA, INC.

Manufacture Dates:

04/07/1998 - 08/18/1998

Potential Units Affected:

7794

Defect Description:

VEHICLE DESCRIPTION: 1998-1999 TOYOTA SPORT UTILITY VEHICLES AND LIGHT DUTY TRUCKS EQUIPPED WITH WHEEL LUG NUTS, PART NO. 1207, SUPPLIED BY PRIME WHEEL CORPORATION, AND DISTRIBUTED BY GULF STATES TOYOTA, INC. IN THE STATES OF TEXAS, OKLAHOMA, ARKANSAS, LOUISIANA, AND MISSISSIPPI ONLY. THE LUG NUTS CONTAIN A DEFECT WHICH COULD CAUSE LOSS OF THE LUG NUTS, AND POSSIBLE LOSS OF THE WHEEL.

Consequence:

THIS CONDITION COULD CAUSE LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.

Action to take:

DEALERS WILL REPLACE ALL THE WHEEL LUG NUTS AND ALSO PERFORM A COMPLIMENTARY WHEEL ROTATION WHEN THE REPAIR IS DONE.

2016 Tesla Model S 2016.5 4dr Sdn AWD 90D

Electronic Stability Control (ESC)
ABS And Driveline Traction Control
Side Impact Beams
Dual Stage Driver And Passenger Seat-Mounted Side Airbags
Front And Rear Parking Sensors
Blind Spot Sensor
Forward Collision and Rear Collision
Lane Departure Warning
Tire Specific Low Tire Pressure Warning
Dual Stage Driver And Passenger Front Airbags
Curtain 1st And 2nd Row Airbags
Airbag Occupancy Sensor
Driver And Passenger Knee Airbag
Restricted Driving Mode
Power Rear Child Safety Locks
Outboard Front Lap And Shoulder Safety Belts -inc: Rear Center 3 Point and Pretensioners
Back-Up Camera
Front Camera
Passenger Air Bag Sensor
Driver Air Bag
Passenger Air Bag
Knee Air Bag
Front Head Air Bag
Rear Head Air Bag
Front Side Air Bag
Stability Control
Brake Assist
Lane Departure Warning
Headlights-Auto-Leveling
Cross-Traffic Alert
Blind Spot Monitor
Daytime Running Lights
Child Safety Locks
Traction Control

Crash Test Results for the 2016 Tesla Models:

No crash test results exist

Service Bulletins for 2016 Tesla Model S 2016.5 4dr Sdn AWD 90D

2016 TESLA MODEL S:

Bulletin Number: SB1313001R6
THIS SERVICE BULLETIN CONTAINS INSTALLATION INSTRUCTIONS FOR THE OPTIONAL THIRD ROW SEAT. INCLUDED IN THIS PROCEDURE ARE STEPS TO ADD THE REAR CROSSMEMBER (IF NEEDED), REMOVE AND MODIFY EXISTING TRIM PANELS, INSTALL HARDWARE, ADD THE 2ND RO

Bulletin Number: SB1315007R3
DESCRIBES HOW TO INSTALL THE CENTER CONSOLE FLOOR FINISHER TO MATCH THE DASH TRIM APPEARANCE.

Bulletin Number: SB1315014R4
DESCRIBES HOW TO INSTALL THE 1ST GENERATION PREMIUM CENTER CONSOLE ASSEMBLY.

Bulletin Number: SB1344010R4
UPGRADE A VEHICLE FROM A SINGLE 2ND GENERATION CHARGER TO DUAL 2ND GENERATION CHARGERS.

Bulletin Number: SB-13-90-002 R3
Instructions for installing the carbon fiber spoiler.

Bulletin Number: SB-15-16-003 R1
It is possible to accidentally break off the aeroshield support tab from the HV Battery. If the tab breaks, the mid aeroshield is not fully supported, reducing the aerodynamic efficiency of the vehicle. The operation of the HV Battery is no

Bulletin Number: SB1615001
DESCRIBES HOW TO RETROFIT THE 2ND GENERATION PREMIUM CENTER CONSOLE ASSEMBLY.

Bulletin Number: SB-16-17-010
On some Model S vehicles, the G625 ground branch of the front body electrical harness might have extra slack. This might cause chafing or other damage to the ground cable.

Bulletin Number: SB-16-44-004
Some third generation chargers could have an internal fault that prevents DC fast charging (Supercharging or CHAdeMO).

Bulletin Number: SB1690001
DESCRIBES HOW TO INSTALL THE PERFORMANCE PEDAL SET ACCESSORY.

Bulletin Number: SB-17-10-001
On some Model S vehicles, the leading edge of the glass roof might be a source of wind noise.

Bulletin Number: SB-17-10-006 R1
On Model S, the windshield wiper motor bracket might become loose, resulting in a popping or clicking noise during windshield wiper operation.

Bulletin Number: SB-17-13-002
On some Model S and Model X vehicles, the connection of the hook-and-loop material that secures the seat upholstery to the seat cushion foam might weaken, causing the upholstery to gather and cause wrinkles.

Bulletin Number: SB-17-13-005 R2
On some Model S and Model X front seats, the forward inboard Huck BOM fastener and pivot bushing (nearest to the center console) used on the front lift links may develop an interactive clearance condition, which might result in a rocking mo

Bulletin Number: SB-17-13-005 R3
On some Model S and Model X front seats, the forward inboard Huck BOM fastener and pivot bushing (nearest to the center console) used on the front lift links may develop an interactive clearance condition, which might result in a rocking mo

Bulletin Number: SB-17-17-002
On some vehicles with 2nd generation Autopilot, the forward facing camera pitch (vertical angle) might be out of the specifications required for some future Autopilot features.

Bulletin Number: SB-17-17-002 R1
On some Model S and Model X vehicles with 2nd generation Autopilot, the forward facing camera pitch (vertical angle) might be out of the specifications required for some future Autopilot features.

Bulletin Number: SB-17-17-002 R2
On some Model S and Model X vehicles with 2nd generation Autopilot, the forward facing camera pitch (vertical angle) might not conform to internal specifications.

Bulletin Number: SB-17-17-002 R3
On some Model S and Model X vehicles with 2nd generation Autopilot, the forward facing camera pitch (vertical angle) might not conform to internal specifications.

Bulletin Number: SB-17-31-001
Some Model S and Model X vehicles may have been manufactured with front suspension fore links that may not meet Tesla strength specifications. In the event of link failure, the driver can still maintain control of the vehicle but the tire m

Bulletin Number: SB-18-13-002
On some Model S base trim 1st row seats, the Huck BOM fastener and pivot bushing used on the front lift links may develop an interactive clearance condition, which might result in a rocking motion in the seat. This does not affect performan

Bulletin Number: SB-18-13-002 R1
On some Model S base trim front seats, the forward inboard Huck BOM fastener and pivot bushing (nearest to the center console) used on the front lift links may develop an interactive clearance condition, which might result in a rocking moti

Bulletin Number: SB-18-13-002 R2
On some Model S base trim front seats, the forward inboard Huck BOM fastener and pivot bushing (nearest to the center console) used on the front lift links may develop an interactive clearance condition, which might result in a rocking moti

Bulletin Number: SB-18-15-006
On some Model X vehicles, incorrect routing of the intrusion sensor wires might result in electrical interference between the intrusion sensor and the intrusion sensor electrical control unit (ECU). The electrical interference causes the ca

Bulletin Number: SB-18-31-001
Some Model S vehicles were manufactured with front suspension lower fore links that do not meet Tesla?s internal specifications. The lower fore link may contact the sway bar mounting bracket, causing noise and the risk for damage to front s

Bulletin Number: SB-18-32-002 R1
Long-term exposure to high-corrosion environments might weaken the bolts that attach the power steering motor to the steering rack housing.

Bulletin Number: SB-18-32-002 R3
Long-term exposure to high-corrosion environments might weaken the bolts that attach the power steering motor to the steering rack housing.

Bulletin Number: SB-19-20-001
The propellant in the front passenger airbag inflator might degrade over time, which could cause the inflator body to rupture in the event the airbag is deployed.

Bulletin Number: SB-19-20-001 R1
The propellant in the front passenger airbag inflator might degrade over time, which could cause the inflator body to rupture in the event the airbag is deployed.

Bulletin Number: SB-19-39-001
During hard acceleration, the driver might notice vibrations coming from the front of some Model S or Model X vehicles.

Bulletin Number: SB-19-39-001 R2
Older versions of the Model S and Model X LH front drive unit clevis mount contain a bushing that allows the front drive unit to move side-to-side more than expected during hard accelerations, resulting in excessive vibrations coming from t

Recalls for 2016 Tesla Model S 2016.5 4dr Sdn AWD 90D

2016 TESLA MODEL S

NHTSA Campaign ID:

17V260000

Component:

PARKING BRAKE

Manufacturer:

Tesla Motors, Inc.

Manufacture Dates:

07/12/2012 - 11/17/2016

Potential Units Affected:

31709

Defect Description:

Tesla, Inc. (Tesla) is recalling certain 2016 Model S and Model X vehicles. The electric parking brake calipers have an internal gear that may be improperly manufactured, possibly resulting in the gear fracturing during parking brake application or release.

Consequence:

If the gear breaks during parking brake release, the vehicle will not be able to be moved. If the gear breaks during parking brake application, the parking brake may not adequately hold the vehicle, potentially resulting in the vehicle rolling, increasing the risk of a crash.

Action to take:

Tesla will notify owners, and service centers will replace the electric parking brake calipers, free of charge. A remedy is currently unavailable. Interim notices informing owners of the safety risk were mailed June 8, 2017. Owners will receive a second notice when the remedy becomes available. Owners may contact Tesla customer service at 1-877-798-3752. Tesla's number for this recall is SB-17-33-002.

2016 TESLA MODEL S

NHTSA Campaign ID:

18V204000

Component:

STEERING:ELECTRIC POWER ASSIST SYSTEM

Manufacturer:

Tesla, Inc.

Manufacture Dates:

05/31/2012 - 04/09/2016

Potential Units Affected:

70421

Defect Description:

Tesla, Inc. (Tesla) is recalling certain 2012-2016 Tesla Model S vehicles equipped with Bosch steering racks. The aluminum bolts that attach the power steering gear assist motor to the gear housing may corrode and fracture causing a reduction or complete loss of power steering assist.

Consequence:

Loss of power steering assist would require a higher steering effort, especially at lower speeds, which may increase the risk of a crash.

Action to take:

Tesla will notify owners, and Tesla Service Centers will replace the steering gear mounting bolts and add a corrosion-preventative sealer, free of charge. The recall began May 7, 2019. Owners may contact Tesla customer service at 1-877-798-3752. Tesla's number for this recall is SB-18-32-002.

2016 TESLA MODEL S

NHTSA Campaign ID:

19V002000

Component:

AIR BAGS:PASSENGER SIDE FRONTAL

Manufacturer:

Tesla, Inc.

Manufacture Dates:

01/01/2014 - 12/09/2016

Potential Units Affected:

68673

Defect Description:

Tesla, Inc. (Tesla) is recalling all 2014-2016 Model S vehicles equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence:

An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Action to take:

Tesla will notify owners, and Tesla Service Centers will replace the passenger frontal air bag modules, free of charge. The recall began May 29, 2019. Owners may contact Tesla customer service at 1-877-798-3752. Tesla's number for this recall is SB-19-20-001.

USED CAR BUYER'S GUIDE

1998 Toyota Corolla 4dr Sdn LE Auto

2016 Tesla Model S 2016.5 4dr Sdn AWD 90D